First: First of all, pay attention to whether the interface and elbow are leaking oil, and whether the sealing work is done well. Second: The use of engine oil will be more than before installing the oil cooling, because the oil cooling needs to store a certain amount of oil. When changing the oil, the oil in the oil cooling must be cleaned up.
Mineral oil and fully synthetic oil cannot be mixed. From a technical point of view, it is no problem to mix different types of engine oil. However, it should be noted that while mixing oil, you are also mixing the additives in them. It is not necessarily a good thing to mix the additives in different oils.
The oil cooling area is selected reasonably, the installation position is also reasonable, and the installation method must be correct.The specific oil cooling effect varies according to each machine, and the oil cooling measurement should be tested under the guidance of professionals.
For this reason, the following are a few issues that need to be paid attention to when using the engine in winter: add antifreeze. If the engine can start smoothly, it is best to use antifreeze as coolant. The quality of the selected antifreeze must be qualified, especially the pH and stability of the antifreeze must meet the requirements, otherwise it will corrode the waterway and water seal, causing water leakage and other faults.
1. It can't be changed. The cylinder head, cylinder block, engine whole box and many other parts of the air-cooled engine and water-cooled engine are completely different. The only way to change is to change the engine assembly, but it can be modified.Oil cooling, which is relatively easy, but it is difficult to say how much stronger the effect is than the current air cooling, and the effect is not very big.
2. When many drivers do maintenance in 4S stores, they will be persuaded by the staff to install oil cooling on the water-cooled engine. In fact, this is not necessary. Most cars on the market use three types of coolant, including ethylene glycol antifreeze, anhydrous antifreeze and cooling oil.
3. Water cooling: The water-cooled spindle is easy to rust, and the water source needs to be replaced frequently. The refrigeration method of the water cooler is only fan refrigeration, fan heat dissipation, and there is no refrigeration system itself.
4. Is LZ air-cooled to oil-cooled or water-cooled to oil-cooled? There is no need to change air cooling to oil cooling. Air cooling has met the requirements of heat dissipation. Water cooling to oil cooling is not good. The specific heat capacity of water and the specific heat capacity of oil are different. The temperature of oil generally rises faster, and the requirements for heat dissipation device are relatively high.
5. Hello, it's okay, but it's too expensive. Oil-cooled maintenance-free for life. [ If there is a problem with the car, ask the car master. 4S store professional technician, 10 minutes to solve.
Water-cooled motor is better. Smell and cost. In terms of cost. Large electric spindle water cooling canBy selecting high-quality coolants, such as special coolants for automobiles, it reduces the possibility of corrosion, and also increases the cooling effect to ensure that the spindle is working at the appropriate temperature. The discharge and treatment of wastewater are more environmentally friendly than oil products.
Water cooling is good. Nowadays, many models on the market adopt water-cooled engine cooling. Water cooling is to cool the engine with water. The purpose of cooling the engine through various tools. Therefore, its cooling method. It's relatively simple. The cooling effect is also relatively good, although the effect is relatively good.
In theory, oil cooling is better. Cooling time: Because the cooling speed of oil is slower than that of water, the cooling time of oil cooling is longer than that of water cooling. Hardness of quenching: high water cooling, low oil cooling. Chen quenching deformation: large water cooling, small oil cooling. The tendency of quenching cracking: large water cooling and small oil cooling.The depth of the quenching layer: deep water cooling, shallow oil cooling.
"The following is my personal opinion: Generally speaking, water cooling is better, the oil-cooled engine is easy to overheat, and the radiator is relatively large: the specific capacity of oil is too small, and water has the largest specific heat capacity in nature, that is, the water temperature rises by 1 degree and absorbs more heat than oil.
Shipping lane performance metrics-APP, download it now, new users will receive a novice gift pack.
First: First of all, pay attention to whether the interface and elbow are leaking oil, and whether the sealing work is done well. Second: The use of engine oil will be more than before installing the oil cooling, because the oil cooling needs to store a certain amount of oil. When changing the oil, the oil in the oil cooling must be cleaned up.
Mineral oil and fully synthetic oil cannot be mixed. From a technical point of view, it is no problem to mix different types of engine oil. However, it should be noted that while mixing oil, you are also mixing the additives in them. It is not necessarily a good thing to mix the additives in different oils.
The oil cooling area is selected reasonably, the installation position is also reasonable, and the installation method must be correct.The specific oil cooling effect varies according to each machine, and the oil cooling measurement should be tested under the guidance of professionals.
For this reason, the following are a few issues that need to be paid attention to when using the engine in winter: add antifreeze. If the engine can start smoothly, it is best to use antifreeze as coolant. The quality of the selected antifreeze must be qualified, especially the pH and stability of the antifreeze must meet the requirements, otherwise it will corrode the waterway and water seal, causing water leakage and other faults.
1. It can't be changed. The cylinder head, cylinder block, engine whole box and many other parts of the air-cooled engine and water-cooled engine are completely different. The only way to change is to change the engine assembly, but it can be modified.Oil cooling, which is relatively easy, but it is difficult to say how much stronger the effect is than the current air cooling, and the effect is not very big.
2. When many drivers do maintenance in 4S stores, they will be persuaded by the staff to install oil cooling on the water-cooled engine. In fact, this is not necessary. Most cars on the market use three types of coolant, including ethylene glycol antifreeze, anhydrous antifreeze and cooling oil.
3. Water cooling: The water-cooled spindle is easy to rust, and the water source needs to be replaced frequently. The refrigeration method of the water cooler is only fan refrigeration, fan heat dissipation, and there is no refrigeration system itself.
4. Is LZ air-cooled to oil-cooled or water-cooled to oil-cooled? There is no need to change air cooling to oil cooling. Air cooling has met the requirements of heat dissipation. Water cooling to oil cooling is not good. The specific heat capacity of water and the specific heat capacity of oil are different. The temperature of oil generally rises faster, and the requirements for heat dissipation device are relatively high.
5. Hello, it's okay, but it's too expensive. Oil-cooled maintenance-free for life. [ If there is a problem with the car, ask the car master. 4S store professional technician, 10 minutes to solve.
Water-cooled motor is better. Smell and cost. In terms of cost. Large electric spindle water cooling canBy selecting high-quality coolants, such as special coolants for automobiles, it reduces the possibility of corrosion, and also increases the cooling effect to ensure that the spindle is working at the appropriate temperature. The discharge and treatment of wastewater are more environmentally friendly than oil products.
Water cooling is good. Nowadays, many models on the market adopt water-cooled engine cooling. Water cooling is to cool the engine with water. The purpose of cooling the engine through various tools. Therefore, its cooling method. It's relatively simple. The cooling effect is also relatively good, although the effect is relatively good.
In theory, oil cooling is better. Cooling time: Because the cooling speed of oil is slower than that of water, the cooling time of oil cooling is longer than that of water cooling. Hardness of quenching: high water cooling, low oil cooling. Chen quenching deformation: large water cooling, small oil cooling. The tendency of quenching cracking: large water cooling and small oil cooling.The depth of the quenching layer: deep water cooling, shallow oil cooling.
"The following is my personal opinion: Generally speaking, water cooling is better, the oil-cooled engine is easy to overheat, and the radiator is relatively large: the specific capacity of oil is too small, and water has the largest specific heat capacity in nature, that is, the water temperature rises by 1 degree and absorbs more heat than oil.
Supply chain optimization with trade data
author: 2024-12-23 22:21Global supplier scorecard templates
author: 2024-12-23 22:21Global import export freight indexes
author: 2024-12-23 20:45Global trade indices and benchmarks
author: 2024-12-23 22:49HS code intelligence for oil and gas industry
author: 2024-12-23 20:52How to comply with origin rules
author: 2024-12-23 20:48Trade data for pharmaceuticals supply chain
author: 2024-12-23 20:47How to find reliable global suppliers
author: 2024-12-23 20:43536.87MB
Check982.96MB
Check972.12MB
Check281.85MB
Check253.86MB
Check481.96MB
Check196.46MB
Check843.56MB
Check795.66MB
Check798.84MB
Check752.63MB
Check155.62MB
Check389.11MB
Check378.71MB
Check721.62MB
Check912.22MB
Check245.32MB
Check338.83MB
Check112.21MB
Check246.72MB
Check799.54MB
Check581.55MB
Check871.15MB
Check124.15MB
Check358.89MB
Check968.53MB
Check891.84MB
Check411.68MB
Check211.44MB
Check837.95MB
Check277.28MB
Check288.43MB
Check285.25MB
Check733.79MB
Check487.99MB
Check977.96MB
CheckScan to install
Shipping lane performance metrics to discover more
Netizen comments More
504 HS code alignment with labeling standards
2024-12-23 22:47 recommend
504 Global trade news aggregation
2024-12-23 22:44 recommend
1009 Asia trade corridors HS code mapping
2024-12-23 22:33 recommend
2914 FMCG sector HS code analysis
2024-12-23 21:16 recommend
374 Navigating HS code rules in Latin America
2024-12-23 20:53 recommend