Data-driven supplier diversity programs

List of catalogs of this article:

• 1, How to install the car door panel latch?
• 2, car seat belt buckle replacement
• 3, Automobile snap disassembly method
• 4, How to install the car inner lining
• 5、 How to use the car lining snap?

How to install the car door panel latch?

1. First, open the door of the Focus, place the door panel snap on the door panel and align it according to the position of the mounting hole on the snap. Secondly, use a screwdriver and a wrench to fix the door panel snap to the door panel.Note that the screws should be firmly tightened so as not to affect the use of the door.

2. Open the door and check the fixing method of the door interior panel. Generally speaking, the fixing methods of the door interior panel include buckle fixing and screw fixing, which need to be judged according to the model and specific situation.

3. The installation method of crv front door decorative panel snap is as follows. Disassemble the original triangle plate (treble position). Pry open the plastic plate marked 2 and remove the internal screws. Remove the two fixing screws marking 3 chrome-plated decorative panels and pull out the decorative panels to the left. Remove the fixing bolt at the lock head.

4. The installation method of the guard plate latch under the Mazda door is to pry the trim panel inside the door panel and the miscellaneous box, and pry the plastic plate at the back of the door panel. Remove the fixed thread and remove the door plate.The net cover, slowly pry the door panel from here. After prying open all the snaps, just like the ordinary door panel, you can remove the door panel by lifting it slightly up.

5. Remove the door glass lifting switch of Rongwei 550 first. Remove the door interior panel glass switch trim panel. Remove the harness plug of the interior panel of the door. Remove the screws that fix the interior panel of the door. Pry open the snaps inside the door one by one and install them.

6. Car door panel snap disassembly method 1 can be opened as follows: First of all, find a small hole under the handlebar in the cockpit. After that, remove the physical key on the car key, and you can also use objects such as small cones. Aim the physical key at the hole. Under normal circumstances, the physical key matches the hole.

Car seat belt buckle replacement

1. Replace the Aize 5 seat belt buckle, first pry the plastic buckle with a screwdriver, remove the old buckle, replace it with a new buckle, and finally install the plastic buckle. Back. Car snaps are divided into plastic snaps and nylon snaps according to materials, and the quality is also very good.

2. The method of replacing the car seat belt buckle is as follows:Pull the upper end of the seat belt down until the end of the belt is completely placed on the door frame, which releases the lock in the tractor, and the seat belt can now be adjusted. When the car is placed in an automatic device, the seat belt cannot be locked, moved or adjusted.

3. Steps to remove the seat belt slot: first adjust the seat and remove the four fixing bolts on the front and rear sides of the seat. After the disassembly is completed, find the line of the car seat and remove the induction line of the safety buckle.

4. Generally, it is recommended to go directly to a 4S store or a professional auto repair shop to replace it. Because the snap is not easy to repair (it can be said that it is basically impossible to repair), once an accident occurs, the snap will have to withstand a lot of force, and it will be very dangerous if there is a problem. And it's not expensive to change this, usually dozens of yuan.

Disassembly method of various snaps of cars

Disassembly method of car lining buckle: The disassembly method of trunk lining buckle is simple, no need to ask. It's a miracle to ask. Use a special tool or a small flat-head screwdriver to pry open the middle round head, and then wedge or pull it out with a tool. It is normal for the teeth to slide in smoothly, and the teeth are stuck in reverse. The snap is directly exposed and inserted into the hole of the metal plate.

Prepare the necessary tools for removing the latch in advance, such as a cross-mouthed or hexagonal prismal wrench. Insert the cross end of the small wrench into the knife groove directly opposite the expansion snap, and then turn the small wrench in the opposite direction until the snap is screwed to a certain level, and then take it out.

Removing the car buckle requires certain skills. The specific steps are as follows: preparation tools: car buckle removal tools, wooden sticks, gear tools.Use the car buckle removal tool to open the buckle clip and slowly release the buckle to remove it. Use a wooden stick instead of the gear tool to open the screw of the installed latch.

Find a flat wooden board or steel plate (high hardness), insert it through the gap between the door core plate and the door sheet metal, move it to a place with a snap and pry it up with a little force to make the snap detach. Just pry up all the snaps along the upturned wing in turn.

First, adjust the seat and remove the four fixing bolts on the front and rear sides of the seat. After the disassembly is completed, find the line of the car seat and remove the induction line of the safety buckle.

How to install the car lining snap

How to use the car lining snap:Remove the original interior panel, choose your favorite thicker fabric, paste it on the outer layer of the interior panel (the side that can be seen in the car), use better glue, wrap the edge of the panel, and then work hard on the interior panel.

Tie it with thin wire and fix it with screws. It is recommended to find a sleeper from a repair shop to help you solve it. It is estimated that the lining falls off because of the snap of the lining, which can only be achieved by removing the wheels and buying some snaps and reinstalling them. It's easy to get up. The installation method of the car lining buckle is one-time.

The following is the installation method of the car lining: remove the wheels first, and most of the car linings will be fixed with screws and plastic buttons. The key is how to remove and reinstall them correctly. First, look at the front wheel on either side. Find the inverted U-shaped plastic plate covering the wheel.

First of all, you can gently pry it open with a screwdriver before pulling it out. There are also professional disassembly tools, which can be purchased in some stores or online. Secondly, if the snaps are damaged, they can be easily replaced, because they only cost a few cents.

Replacement method of the car lining plate snap: you can use a word change cone to slowly pry and then pull it out. There is also a professional tool to disassemble the snap, which is sold in some stores or online, and car enthusiasts can buy it; it doesn't matter if the snap is broken, because the snap is only a few cents each, and it can be disassembled. Change to a new one.

How to use the car lining snap?

1. This is usually fixed by a buckle. If it falls off, it should be caused by the snap falling off. You can fix it with Zigong screws by yourself, or you can go to the repair shop to fix it with plastic buckles.

2. The snaps worn inside the car lining snap are all plastic or iron sheet, and you can use force: leaf plate is also called wing plate, including rear leaf plate, rear leaf plate lining, and rear fender.

3. Grab the latch on the car body with your hand, and there are buttons at both ends, and you can install it. The snaps of the car lining are basically made of plastic or iron, which can be used force: 1. The wing plate is also called the fender, including the rear wing plate, the rear wing plate lining and the rear wing plate.

4. It can be directly inserted into the corresponding hole. There are 2 types of car snaps according to the material category: plastic snaps and nylon snaps. Plastic snaps are usually special snaps for auto repair shops, and their product quality is also very good. However, nylon snaps are relatively better, and the price of natural nylon snaps is much higher than that of plastic snaps.

5. How to open the snap of the car lining: Special tools are required to remove it. You can borrow one from the garage. If you don't want to borrow it, you can pry it open. Find the top of the main buckle of an item card and pull it up to remove it. If you can't find a useful tool, find a screwdriver to pry it open little by little.