. Loosen the gas screw on the diesel filter 2. Press the pump oil handle on the oil transmission pump 3. Observe the loosened degassing screw, the discharged fuel has bubbles, continue to press the pump handle on the oil transmission pump until the fuel does not contain bubbles, and then tighten the deflating screw on the diesel filter.
First of all, you need to find the hand oil pump of the vehicle; secondly, press the hand oil pump hard to extract the air inside the diesel from the fuel tank and transport it to the high-pressure oil pump at a certain pressure. However, before exhausting, the owner must ensure that the fuel supply pipe of the vehicle is well sealed and there is no leakage.
Before refueling, first open the fuel tank cover, find the exhaust port on the fuel tank, and open the exhaust port with the exhaust screw to release the air in the fuel tank. Start refueling. When refueling, you should inject fuel slowly to avoid too fast or too urgent, so as to avoid bubbles.
The first task is to press the hand oil pump handle repeatedly, which takes a long time. Then loosen the oil screw and tighten it immediately after the bubbles are discharged. Repeat several times until there are no bubbles. Remember the precautions when exhausting.
1,. Press the oil pump handle on the oil transmission pump to observe that the loose air release screw on the fuel injection pump has bubbles. At this time, continue to press the pump oil handle until the fuel does not contain bubbles to stop pumping oil, and then tighten the degassing screw on the fuel injection pump.
2. Before refueling, open the fuel tank cover, find the exhaust port on the fuel tank, and open the exhaust port with the exhaust screw to release the air in the fuel tank. Start refueling. When refueling, you should inject fuel slowly to avoid too fast or too urgent, so as to avoid bubbles.
3. If on the way,If you need to exclude the air in the oil line, you can first release the degassing screw on the fuel injection pump or loosen any joint between the diesel filter and the fuel injection pump, and then drive the mechanical oil pump through the start. The leak point will spray out smooth and bubble-free fuel. At this time, just tighten the above leak point you have loosened.
4 、
5. Hello, there is an exhaust bolt on the manual oil pump (oil-water separator) of the distributed diesel pump engine. Loosen the exhaust bolt and press the pump rod of the manual pump by hand until there is no air in the diesel out of the exhaust hole, and then tighten the exhaust bolt.
6. Press the oil pump handle on the oil transmission pump until the fuel does not contain bubbles to stop pumping oil. Just tighten the exhaust bolt or install the oil pipe inserted into the diesel filter.
Unscrew any exhaust screw at the upper end of both sides of the fuel injection pump with a screwdriver or wrench several times, and press the manual oil pump with your hand until the discharged diesel is continuous, without bubbles, and makes a "squeaky" sound. Then screw the degassing screw and manually press the oil pump back to its original position.
To exhaust the air of the diesel engine, first find the exhaust screw on the oil pump, unscrew it with a wrench, find the hand oil pump, pump the oil hard, and wait for the sound. There will be a large outflow of diesel, tighten the bolts, and then pump oil. After the oil flows out of the return oil pipe, it proves that the exhaust is successful.
Press the oil pump handle on the oil pump until the fuel is free of bubbles to stop pumping the oil. Just tighten the exhaust bolt or install the oil pipe inserted into the diesel filter.
The method of diesel exhaust of Weichai 490 engine is to hold the exhaust screw on the filter seat and exhaust it without moving. The conventional method is to unscrew any exhaust screw at the top of both sides of the fuel injection pump with a screwdriver or wrench several times, and press the manual oil pump by hand until the discharged diesel is continuously, smooth without bubbles, and makes a squeaking sound.
The method of excluding air entering the low-pressure oil road. For diesel engines with oil transmission pumps, you can open air holes and press the hand pressure gauge to exclude air. For diesel engines without oil transmission pumps, you can loosen the venting screw on the fuel injection pump to make the diesel with bubbles overflow, and tighten the screws when there is no bubbles flowing out.Exclude the air from the high-pressure oil line.
HS code alignment with import quotas-APP, download it now, new users will receive a novice gift pack.
. Loosen the gas screw on the diesel filter 2. Press the pump oil handle on the oil transmission pump 3. Observe the loosened degassing screw, the discharged fuel has bubbles, continue to press the pump handle on the oil transmission pump until the fuel does not contain bubbles, and then tighten the deflating screw on the diesel filter.
First of all, you need to find the hand oil pump of the vehicle; secondly, press the hand oil pump hard to extract the air inside the diesel from the fuel tank and transport it to the high-pressure oil pump at a certain pressure. However, before exhausting, the owner must ensure that the fuel supply pipe of the vehicle is well sealed and there is no leakage.
Before refueling, first open the fuel tank cover, find the exhaust port on the fuel tank, and open the exhaust port with the exhaust screw to release the air in the fuel tank. Start refueling. When refueling, you should inject fuel slowly to avoid too fast or too urgent, so as to avoid bubbles.
The first task is to press the hand oil pump handle repeatedly, which takes a long time. Then loosen the oil screw and tighten it immediately after the bubbles are discharged. Repeat several times until there are no bubbles. Remember the precautions when exhausting.
1,. Press the oil pump handle on the oil transmission pump to observe that the loose air release screw on the fuel injection pump has bubbles. At this time, continue to press the pump oil handle until the fuel does not contain bubbles to stop pumping oil, and then tighten the degassing screw on the fuel injection pump.
2. Before refueling, open the fuel tank cover, find the exhaust port on the fuel tank, and open the exhaust port with the exhaust screw to release the air in the fuel tank. Start refueling. When refueling, you should inject fuel slowly to avoid too fast or too urgent, so as to avoid bubbles.
3. If on the way,If you need to exclude the air in the oil line, you can first release the degassing screw on the fuel injection pump or loosen any joint between the diesel filter and the fuel injection pump, and then drive the mechanical oil pump through the start. The leak point will spray out smooth and bubble-free fuel. At this time, just tighten the above leak point you have loosened.
4 、
5. Hello, there is an exhaust bolt on the manual oil pump (oil-water separator) of the distributed diesel pump engine. Loosen the exhaust bolt and press the pump rod of the manual pump by hand until there is no air in the diesel out of the exhaust hole, and then tighten the exhaust bolt.
6. Press the oil pump handle on the oil transmission pump until the fuel does not contain bubbles to stop pumping oil. Just tighten the exhaust bolt or install the oil pipe inserted into the diesel filter.
Unscrew any exhaust screw at the upper end of both sides of the fuel injection pump with a screwdriver or wrench several times, and press the manual oil pump with your hand until the discharged diesel is continuous, without bubbles, and makes a "squeaky" sound. Then screw the degassing screw and manually press the oil pump back to its original position.
To exhaust the air of the diesel engine, first find the exhaust screw on the oil pump, unscrew it with a wrench, find the hand oil pump, pump the oil hard, and wait for the sound. There will be a large outflow of diesel, tighten the bolts, and then pump oil. After the oil flows out of the return oil pipe, it proves that the exhaust is successful.
Press the oil pump handle on the oil pump until the fuel is free of bubbles to stop pumping the oil. Just tighten the exhaust bolt or install the oil pipe inserted into the diesel filter.
The method of diesel exhaust of Weichai 490 engine is to hold the exhaust screw on the filter seat and exhaust it without moving. The conventional method is to unscrew any exhaust screw at the top of both sides of the fuel injection pump with a screwdriver or wrench several times, and press the manual oil pump by hand until the discharged diesel is continuously, smooth without bubbles, and makes a squeaking sound.
The method of excluding air entering the low-pressure oil road. For diesel engines with oil transmission pumps, you can open air holes and press the hand pressure gauge to exclude air. For diesel engines without oil transmission pumps, you can loosen the venting screw on the fuel injection pump to make the diesel with bubbles overflow, and tighten the screws when there is no bubbles flowing out.Exclude the air from the high-pressure oil line.
Trade data for public policy design
author: 2024-12-23 20:49Real-time supply chain financing insights
author: 2024-12-23 20:45Real-time HS code tariff updates for ASEAN
author: 2024-12-23 20:33How to identify correct HS codes
author: 2024-12-23 20:01HS code-based green supply chain metrics
author: 2024-12-23 22:24How to identify tariff loopholes
author: 2024-12-23 21:20HS code mapping for ASEAN countries
author: 2024-12-23 21:10Comparative supplier performance data
author: 2024-12-23 20:06HS code-based global trend analysis
author: 2024-12-23 19:58227.89MB
Check139.68MB
Check369.73MB
Check956.63MB
Check364.13MB
Check217.45MB
Check347.18MB
Check978.37MB
Check278.51MB
Check832.56MB
Check747.53MB
Check925.48MB
Check596.93MB
Check274.86MB
Check574.59MB
Check598.86MB
Check962.64MB
Check655.63MB
Check155.41MB
Check582.71MB
Check542.39MB
Check288.79MB
Check815.32MB
Check695.38MB
Check627.82MB
Check521.96MB
Check218.21MB
Check471.55MB
Check459.82MB
Check968.93MB
Check577.37MB
Check998.61MB
Check445.57MB
Check981.77MB
Check459.91MB
Check695.26MB
CheckScan to install
HS code alignment with import quotas to discover more
Netizen comments More
2587 HS code variance across regions
2024-12-23 22:31 recommend
1639 Trade compliance training resources
2024-12-23 21:40 recommend
1551 Real-time freight cost analysis
2024-12-23 20:57 recommend
2099 Long-tail trade keyword research
2024-12-23 20:56 recommend
2792 Global trade event monitoring
2024-12-23 20:30 recommend