International trade law reference data

List of the catalog of this article:

• 1 、What engine does the new Pentium x80 use

What is the reason for the excessive speed of the FAW Pentium X80 engine

The reasons for the overspeeding of the car engine include the sudden increase in the throttle valve opening, the leakage or blockage of the fuel injector, the slippage or damage of the empty clutch, the air intake system Air leakage, insufficient engine output power, etc.

Secondly, it may be caused by improper adjustment of the throttle valve. The throttle valve is one of the important control devices in the engine., it can control the amount of air entering the engine, thus controlling the consumption of fuel and the speed of the engine. If the throttle valve is improperly adjusted, the engine air intake will be too large, resulting in excessive engine speed.

The high engine speed is generally caused by damage to the intake pipe, fuel injector failure, incomplete idle switch, exhaust system failure and other reasons. The intake pipe is damaged. Generally speaking, the opening and air intake of the idling control valve are balanced. If the air intake pipe of the vehicle is damaged and the air leaks, the air intake will be out of balance, resulting in high engine speed.

Analysis of the causes of high engine speed: throttle assembly failure. The throttle valve is a controllable valve that controls the air entering the engine. After the gas enters the intake pipe, it will be mixed with gasoline into a combustible mixture, thus burning. If the throttle valve fails, the opening of the throttle valve will suddenly increase, resulting in a sudden increase in the speed of the vehicle.

The larger the opening of the throttle valve, the higher the rotation speed. The accelerator of the gasoline engine does not control the amount of fuel injection. It controls the opening of the throttle valve. That is, the opening is small, and there is less mixing gas entering the cylinder, so the power emitted by the engine is small, and vice versa is large.

Why is the engine speed of Pentium X80 too high

Ignition coil failure; fuel pump failure, oil line blockage; air conditioning filter blockage Sensors include water temperature, crankshaft position, air flow, inlet temperature Degree, oxygen sensors, etc. When these sensors are damaged, have poor contact or the signal is interrupted, the ECU of the car cannot accurately obtain the data of the engine, which will cause the engine fault light to turn on.

And the interior is withThe current model remains the same, and it is expected that the new model will be further upgraded in terms of configuration to strengthen its market competitiveness.

The reasons why the voltage of the car generator is too high are: (1) The speed is too high. Treatment: Reduce the opening of the water turbine guide wing and reduce the speed. ( 2) The air gap in the iron core of the shunt reactor is too large. Treatment: Change the thickness of the reactor iron core gasket and adjust the air gap. ( 3) The magnetic field variable resistor is short-circuited; the voltage regulation fails. Treatment: Find the short-circuit point and eliminate it.

Hello, the engine or gearbox support, commonly known as the claw, is caused by aging or inadequate installation and other reasons. It needs to be checked to further confirm whether it needs to be replaced; the gearbox hanging shock is caused by the poor operation of the gearbox hydraulic system due to the impurities or dirt of the gearbox oil.

What engine does the new Pentium x80 use

Pentium X80 is a compact S under Pentium UV. The car uses a total of two engines: an 8-liter turbocharged engine and a 0-liter naturally aspirated engine. The length, width and height of Pentium X80 are 4620mm (mm), 1820mm (mm), 1695mm (mm), and the wheelbase is 2675mm (mm).

Pentium x80 is a compact SUV under Pentium. This car uses a total of two engines, one is an 8-liter turbocharged engine and the other is a 0-liter naturally aspirated engine. The length, width and height of Pentium x80 are 4,620 mm, 1820 mm and 1695 mm respectively, and the wheelbase is 2675 mm.

The 0-liter naturally aspirated engine of Pentium x80 has a maximum torque of 147 horsepower and 184 Nm. The maximum power speed of this engine is 6500 rpm and the maximum torque speed is 4,000 rpm. This engine is equipped with multi-point electric injection technology and uses aluminum alloy cylinder head and cylinder block.

Pentium x80 has two engines to choose from. One of them is mainly a 0-liter naturally aspirated engine, and the other uses an 8-liter turbocharged engine. Although turbocharging technology has been widely used in automobile engines, turbocharging engines are not widely used in the whole system of Pentium x80.