How to analyze global export trends

List of the contents of this article:

• 1,Is Wangjiang Legend GN250 the same as Wangjiang Breston 250 engine< /Li>
• 2, domestic r3,250 air-cooled Engine, what size is suitable for the steering bearing of the front flat fork
• 3, Can EN125 replace the engine of GN250?
• 4 、How to the ignition time of the gn250 motorcycle

Is the Wangjiang Legend GN250 and the Wangjiang Breston 250 engine the same

In terms of power, this series of models is equipped with a single-cylinder air-cooled electric injection engine, which comes from Suzuki's early GN250, but in thisThe model has been re-optimized and adjusted, so that the whole machine not only has stable performance, but also has a stronger torque output.

GN250 is almost not sold in Japan. This model is specially designed to supply the markets of China and Southeast Asian countries. Its prototype is TU250 (this is said later).

It should be made clear that not all domestic motorcycles are licensed. Judging from the current situation, only YBR250 and Wangjiang GN250 can successfully obtain the procedures for domestic motorcycles. Miscellaneous goods are likely to be checked by the DMB. There is no filing or model registration. In the end, it is still I can't get a license plate, so I have to ask clearly before I start.

Wangjiang Suzuki GN250 adopts a single-cylinder air-cooled, single-top camshaft and four-valve reinforced engine.The Suzuki TSCC double dome combustion chamber allows it to emit 15 kilowatts of power and 15 Nm of torque, and the fuel consumption per 100 kilometers is only about 3 liters.

The power level is 250, which belongs to the domestic golden displacement, which can fully meet the daily needs.

domestic r3,250 air-cooled engine, how suitable is the steering bearing of the front flat fork

2 rear flat fork bearings: TA2020 (domestic model: HK202720) direction column bearing: upper bearing 32005, lower Bearing 32006.

tons. Revo ta554 tractor is a tractor produced by Revo in 2017. The pressure bearing on the front axle steering pin is 16 tons, which can meet the needs of small and medium-sized transportation and work, and is cost-effective.

The engine generally belongs to the engine. If yours is not a tricycle engine, it should be a cb chain machine. It is recommended to use 10-50 level 4 fully synthetic engine oil. If you have any other questions, you can continue to ask me.

Can EN125 replace the engine of GN250?

But it's okay, but it's too troublesome to perform this operation. First of all, you need to change the frame, otherwise the GN engine is wider than the EN125 and can't be hung up. Second, the rear tire of the EN125 is the 25-18 tire.

Of course not. The cylinder capacity is different, the work ratio is also different, and the transmission ratio and the bearing capacity of the frame cannot be coordinated. The hard installation will greatly affect the stability of the whole vehicle. Ha ha, if you don't want to drive it and fly, it is recommended not to use your brain.

Yes. According to the relevant public information of the query, the gn125 engine can be installed on the en125 frame. An engine is a machine that can convert other forms of energy into mechanical energy, including an internal combustion engine.

How to check the ignition time of gn250 motorcycle

1. The method of gn250 motorcycle to check the ignition time is to first remove the check hole screw on the magnetic motor cover, and start the T-point on the magnetic motor rotor. Check that the holes on the machine are orthogonal, and then the two engravings on the left side of the camshaft are parallel to the plane of the cylinder head. The two cams of the camshaft are inclined downwards, and the fixed pins of the sprocket are installed upwards.

2. The ignition time of the motorcycle is determined by the electronic igniter. To a certain extent, the electronic igniter can change the ignition advance angle according to the limited engine speed, but the ignition time cannot be adjusted manially. The specific operation steps for correct timing are as follows: First, remove the timing cover of the bar head and the crankshaft cover of the engine, as shown in the figure.

3. Put the marker point of the positive wheel against the marker point of the bar head. Tighten the fixing screw of the timing wheel to complete the operation of the motorcycle's timing.

4. Now take the Jialing CJ50 moped as an example, which shows that the optimal ignition time of the motorcycle is 0.91lmm before the stop of the piston. The adjustment method is as follows. 1) Screw off the two M6 screws that fix the outer cover of the magnetic motor and remove the outer cover of the magnetic motor.

5. The number wrench slowly rotates to the right, stop rotating when the spark plug is ignited, and then insert a small starter into the spark plug hole until it touches the piston. At this time, continue to slow the crankshaft to the right. If the starter is pushed out 3 to 4 mm, it is accurate, otherwise adjust (rotate) the platinum bottom plate. Solve it.