1. Excess oil. When adding oil, it is thought that the more the better, exceeding the standard line, so that the engine will produce greater resistance during operation and increase fuel consumption. The increase in the amount of oil in the combustion chamber will increase the amount of carbon accumulated in combustion, the piston movement resistance will increase, and the engine power will decrease.
2. The reason why low-speed or variable-speed cars make buzz is that the gap between the piston and the cylinder wall is too large. During the installation process, when the assembly is too tight and there is abnormal wear, there will be buzzing. Another reason is that the engine knocks on the cylinder. The engine knocks on the cylinder in the initial stage, which may be caused by the early ignition angle or the accumulation of more carbon in the cylinder.
3. The oil level is too low. Maybe there was a noise, but you didn't pay attention. The sound you said was made when the refueling door was very oily. Generally, the bearings in tensioning wheels, generators and pumps have been used to a certain extent and should be replaced.
4. Fault of temperature sensor or temperature regulator. How to solve the buzzing of dk13: The car owner needs to go to the repair shop for inspection and repair in time to avoid any abnormalities during the driving process, causing greater car failures and economic losses to the car owner.
5. There is an abnormal sound in the engine. The abnormal sound in the engine compartment is usually the harsh sound of metal. The abnormal noise of the engine is mainly caused by excessive wear or improper assembly and adjustment of some parts. These abnormal sounds are likely to indicate that the engine is going to fail. Therefore, when the engine makes an abnormal sound, you should go to the repair shop in time to prevent the failure from expanding.
1. By rotating the crankshaft, the timing point corresponds to the black timing point of the upper timing chain. The positive time point correspondence of the intake camshaft is shown in the figure. The positive time point correspondence of the exhaust camshaft is also shown in the figure below. The left balance axis should also be opposite as shown in the figure. The camshaft on the right should also be at the right time.
2. The method of timing chain timing: (1) There are two ways to timing the cam, one is to count the number of teeth. Two pairs of marks.
3. If the intake and exhaust system of the crank connecting rod mechanism of the timing engine gas distribution mechanism cannot be properly coordinated to make the engine work. Timing belt: Timing belt is an important part of the engine gas distribution system. It ensures the accuracy of the intake and exhaust time by connecting with the crankshaft and cooperating with a certain transmission ratio.
4. Adjust the power-off contact gap of the distributor. The size of the contact gap not only affects the strength of the spark, but also affects the opening and closing of the contact. If you adjust the contact gap after adjusting the ignition timing, even if it is a small change.
V29 is the first domestic DK13 all-aluminum VVT engine, which adopts an advanced variable valve timing system, which can fully meet the car Air intake demand when driving at low, medium and high speeds.
Dongfeng Xiaokang V29 is the first domestic DK13 all-aluminum VVT engine, which adopts an advanced variable timing valve system. Dongfeng Xiaokang V29 uses a VVT engine, which can fully meet the air intake needs of cars at low, medium and high speeds.
Reinstall the splitter head, insert the first cylinder high-voltage wire into the plug-in hole where the distributor cover and the distributor head conductor are aligned, and plug in the high-voltage wire of each cylinder in the order of 4 in a clockwise direction.
There is no four-wheel drive model. Dongfeng Xiaokang cars are all rear-wheel drive. 1 Dongfeng Xiaokang v29 is carefully created by Dongfeng Xiaokang Company for eight years. It is carefully created in an environment where there are standard soldiers in front and chase soldiers later. It is the declaration of well-off "specialized in making cars, experts cast quality, professional is leading, dedicated to customers The powerful embodiment of "household" 2.
"The relevant content introduction is as follows: Dongfeng Xiaokang v29: In terms of power, the new car is equipped with 3L and 5L gasoline engines.
The E12 engine of Chang'an truck micro-goods new Chang'an star card MS201 is the best.
The main advantage of the E12 engine is that it adopts German craft quality and Ford-class production management methods, and the E12 engine is equipped with suction gearshift, which saves money and can experience a comfortable sense of control.
Very good. Because the engine of Taurus is an E12 engine, the engine displacement is small, and the power can reach up to 72 kilowatts, which is relatively fuel-efficient, so it is very good. An engine is a machine that can convert other forms of energy into mechanical energy.
DK13 all-aluminum VVT engine adopts an advanced variable timing valve system, and this engine is made of all-aluminum alloy, which is lightweight and dissipates heat quickly.I dare say that the performance is definitely much better than that of the same price.
Not bad. The engine should be replaced regularly with oil and filter elements. The oil quality of any quality oil will change during use. In order to avoid failure, the oil should be changed regularly according to the conditions of use. The engine number of Dongfeng Xiaokang is on the side cylinder block of the engine, and you need to open the engine compartment of the vehicle to see it.
horsepower. Strong power. The new Chang'an Star is equipped with a 2-liter gasoline engine numbered E12, which has never been used before and is a debut. The maximum power is 98 horsepower (72kW)/6000rpm, and the maximum torque of 119N·m can be output when the rotation speed reaches 5000-5500rpm.
HS code-based competitive advantage analysis-APP, download it now, new users will receive a novice gift pack.
1. Excess oil. When adding oil, it is thought that the more the better, exceeding the standard line, so that the engine will produce greater resistance during operation and increase fuel consumption. The increase in the amount of oil in the combustion chamber will increase the amount of carbon accumulated in combustion, the piston movement resistance will increase, and the engine power will decrease.
2. The reason why low-speed or variable-speed cars make buzz is that the gap between the piston and the cylinder wall is too large. During the installation process, when the assembly is too tight and there is abnormal wear, there will be buzzing. Another reason is that the engine knocks on the cylinder. The engine knocks on the cylinder in the initial stage, which may be caused by the early ignition angle or the accumulation of more carbon in the cylinder.
3. The oil level is too low. Maybe there was a noise, but you didn't pay attention. The sound you said was made when the refueling door was very oily. Generally, the bearings in tensioning wheels, generators and pumps have been used to a certain extent and should be replaced.
4. Fault of temperature sensor or temperature regulator. How to solve the buzzing of dk13: The car owner needs to go to the repair shop for inspection and repair in time to avoid any abnormalities during the driving process, causing greater car failures and economic losses to the car owner.
5. There is an abnormal sound in the engine. The abnormal sound in the engine compartment is usually the harsh sound of metal. The abnormal noise of the engine is mainly caused by excessive wear or improper assembly and adjustment of some parts. These abnormal sounds are likely to indicate that the engine is going to fail. Therefore, when the engine makes an abnormal sound, you should go to the repair shop in time to prevent the failure from expanding.
1. By rotating the crankshaft, the timing point corresponds to the black timing point of the upper timing chain. The positive time point correspondence of the intake camshaft is shown in the figure. The positive time point correspondence of the exhaust camshaft is also shown in the figure below. The left balance axis should also be opposite as shown in the figure. The camshaft on the right should also be at the right time.
2. The method of timing chain timing: (1) There are two ways to timing the cam, one is to count the number of teeth. Two pairs of marks.
3. If the intake and exhaust system of the crank connecting rod mechanism of the timing engine gas distribution mechanism cannot be properly coordinated to make the engine work. Timing belt: Timing belt is an important part of the engine gas distribution system. It ensures the accuracy of the intake and exhaust time by connecting with the crankshaft and cooperating with a certain transmission ratio.
4. Adjust the power-off contact gap of the distributor. The size of the contact gap not only affects the strength of the spark, but also affects the opening and closing of the contact. If you adjust the contact gap after adjusting the ignition timing, even if it is a small change.
V29 is the first domestic DK13 all-aluminum VVT engine, which adopts an advanced variable valve timing system, which can fully meet the car Air intake demand when driving at low, medium and high speeds.
Dongfeng Xiaokang V29 is the first domestic DK13 all-aluminum VVT engine, which adopts an advanced variable timing valve system. Dongfeng Xiaokang V29 uses a VVT engine, which can fully meet the air intake needs of cars at low, medium and high speeds.
Reinstall the splitter head, insert the first cylinder high-voltage wire into the plug-in hole where the distributor cover and the distributor head conductor are aligned, and plug in the high-voltage wire of each cylinder in the order of 4 in a clockwise direction.
There is no four-wheel drive model. Dongfeng Xiaokang cars are all rear-wheel drive. 1 Dongfeng Xiaokang v29 is carefully created by Dongfeng Xiaokang Company for eight years. It is carefully created in an environment where there are standard soldiers in front and chase soldiers later. It is the declaration of well-off "specialized in making cars, experts cast quality, professional is leading, dedicated to customers The powerful embodiment of "household" 2.
"The relevant content introduction is as follows: Dongfeng Xiaokang v29: In terms of power, the new car is equipped with 3L and 5L gasoline engines.
The E12 engine of Chang'an truck micro-goods new Chang'an star card MS201 is the best.
The main advantage of the E12 engine is that it adopts German craft quality and Ford-class production management methods, and the E12 engine is equipped with suction gearshift, which saves money and can experience a comfortable sense of control.
Very good. Because the engine of Taurus is an E12 engine, the engine displacement is small, and the power can reach up to 72 kilowatts, which is relatively fuel-efficient, so it is very good. An engine is a machine that can convert other forms of energy into mechanical energy.
DK13 all-aluminum VVT engine adopts an advanced variable timing valve system, and this engine is made of all-aluminum alloy, which is lightweight and dissipates heat quickly.I dare say that the performance is definitely much better than that of the same price.
Not bad. The engine should be replaced regularly with oil and filter elements. The oil quality of any quality oil will change during use. In order to avoid failure, the oil should be changed regularly according to the conditions of use. The engine number of Dongfeng Xiaokang is on the side cylinder block of the engine, and you need to open the engine compartment of the vehicle to see it.
horsepower. Strong power. The new Chang'an Star is equipped with a 2-liter gasoline engine numbered E12, which has never been used before and is a debut. The maximum power is 98 horsepower (72kW)/6000rpm, and the maximum torque of 119N·m can be output when the rotation speed reaches 5000-5500rpm.
Trade data solutions for wholesalers
author: 2024-12-24 01:42HS code-based compliance in bilateral trades
author: 2024-12-24 00:43HS code-based customs dispute resolution
author: 2024-12-24 00:37Country block exemptions by HS code
author: 2024-12-24 00:18Refined metals HS code references
author: 2024-12-23 23:36Canned foods HS code classification
author: 2024-12-24 01:57How to integrate IoT with trade data
author: 2024-12-24 01:11China HS code interpretation guide
author: 2024-12-24 00:33Paper and pulp HS code insights
author: 2024-12-24 00:01Global trade forecasting tools
author: 2024-12-23 23:23833.89MB
Check251.54MB
Check112.25MB
Check366.82MB
Check483.24MB
Check619.99MB
Check385.29MB
Check863.23MB
Check721.18MB
Check175.38MB
Check214.11MB
Check299.48MB
Check866.24MB
Check811.44MB
Check139.35MB
Check167.73MB
Check354.16MB
Check148.72MB
Check218.89MB
Check978.33MB
Check773.92MB
Check322.24MB
Check163.28MB
Check456.92MB
Check439.22MB
Check938.38MB
Check129.33MB
Check987.37MB
Check328.62MB
Check824.67MB
Check672.93MB
Check827.37MB
Check148.32MB
Check581.45MB
Check964.95MB
Check929.43MB
CheckScan to install
HS code-based competitive advantage analysis to discover more
Netizen comments More
1548 International trade event forecasts
2024-12-24 02:03 recommend
1536 global shipment tracking
2024-12-24 01:32 recommend
1917 Import data for raw commodities
2024-12-24 00:59 recommend
2187 Real-time cargo insurance insights
2024-12-23 23:32 recommend
1958 Industry-specific trade growth forecasts
2024-12-23 23:31 recommend